欧美国产日韩另类视频区,2025人妻中文字幕乱码在线,日本三级sm在线观看,小说区图片区另类春色,国产第一浮力影产院路线,欧美亚洲综合图片第一页

lC670MDL740K 離散輸出模塊  GE IC670MDL740 

   IC670MDL740是GE Fanuc公司生產的正邏輯離散輸出模塊。該模塊是一個通用輸出模塊，沿總線接口單元(BIU)安裝，用于實現擴展I/O解決方案.由于IC670MDL740在10-30 VDC的電壓輸出范圍和24VDC的標稱電壓下提供每個通道0.5安培的輸出電流和每個模塊總共4安培的輸出電流，因此它通常用于激勵輸出設備，如指示燈、繼電器線圈、螺線管致動設備和具有低額定電流的類似設備。

IC670MDL740設計有單獨的狀態LED指示燈，指示模塊每個輸出通道的開/關狀態。整個/O組安裝有一個公共保險絲，該保險絲還配有一個led指示燈，用于顯示保險絲熔斷狀態。該模塊產生額定2安培的浪涌電流，最大持續時間為100毫秒。輸出通道最小負載電流為每點1毫安，輸出電壓降為0.5伏，30 VDC時輸出泄漏電流為0.5毫安，開和關信號轉換的典型響應時間。

IC670MDL740配有由25個端子組成的集成端子板。每個端子都設計用于終止一根AWG#14-AWG#22電線或兩根(⑵)使用AWG#18電線的電線。在該模塊上安裝外部跳線后，允許的電線尺寸減小至AWG #14至AWG #16。

現場控制CG670MDL740 DC輸出模塊是GE Fanuc的正邏輯輸出模塊。GE IC670MDL740正邏輯輸出模塊提供一組16個離散輸出通道。這些輸出也充當源類型輸出。輸出點的職責是通過將電流切換到DC電源的正極來為負載提供電流。模塊內有一個5安培的保險絲，用于連接外部電源。輸出具有在10至30伏DC范圍內切換負載的能力，同時提供每點0.5安培的最大電流。每個輸出都連接到一個狀態指示燈LED，以指示該輸出的開/關狀態。IC670MDL740正邏輯輸出模塊從總線接口單元的電源汲取111毫安的最大電流。模塊的狀態指示器指示保險絲熔斷故障，以及用戶電源電壓是否低于9.8伏DC。如果電源連接不正確，就會燒斷保險絲。這意味著保險絲有助于保護輸出免受外部電源極性錯誤的影響。它還有助于保護模塊免受流經輸出點的過大電流的影響。建議用戶使用額定電流為5安培、額定交流電壓為250伏的慢熔型保險絲。該模塊還可以向總線接口單元發送保險絲熔斷診斷信息。IC670MDL740正邏輯輸出模塊的最大浪涌電流為2安培，最大負載電流為0.5安培，每點最小負載電流為1毫安。

The IC670MDL740 is a positive logic discrete output module produced by GE Fanuc. The module is a universal output module that is installed along the Bus Interface Unit (BIU) to implement an extended I/O solution. Since the IC670MDL740 provides an output current of 0.5 amps per channel and a total of 4 amps per module at a voltage output range of 10-30 VDC and a nominal voltage of 24VDC, it is commonly used to excite output devices such as indicator lights, relay coils, solenoid actuation devices, and similar devices with low current ratings.

The IC670MDL740 is designed with a separate status LED indicator indicating the on/off status of each output channel of the module. A common fuse is installed throughout the /O group, which is also equipped with an led indicator to indicate the blown fuse status. The module generates an inrush current rated at 2 amps for a maximum duration of 100 milliseconds. The minimum load current of the output channel is 1 MA per point, the output voltage drop is 0.5 V, the output leakage current is 0.5 MA at 30 VDC, and the typical response time for on and off signal conversion.

The IC670MDL740 is equipped with an integrated terminal board consisting of 25 terminals. Each terminal is designed to terminate one AWG#14-AWG#22 wire or two (2) wires using AWG#18 wires. After installing external jumpers on this module, the allowable wire size is reduced to AWG #14 to AWG #16.

Field control CG670MDL740 DC output module is the positive logic output module of GE Fanuc. The GE IC670MDL740 positive logic output module provides a set of 16 discrete output channels. These outputs also act as source type outputs. The responsibility of the output point is to provide current to the load by switching the current to the positive terminal of the DC power supply. There is a 5 amp fuse inside the module to connect to an external power supply. The output has the ability to switch loads in the 10 to 30 volt DC range while providing a maximum current of 0.5 amps per point. Each output is connected to a status indicator LED to indicate the on/off status of that output. The IC670MDL740 positive logic output module draws a maximum current of 111 mA from the power supply of the bus interface unit. The module's status indicator indicates a blown fuse failure and if the user's supply voltage is below 9.8 V DC. If the power is not connected correctly, it will blow the fuse. This means that the fuse helps protect the output from polarity errors in the external power supply. It also helps protect the module from excessive current flowing through the output point. It is recommended that users use a slow fuse with a rated current of 5 amps and rated AC voltage of 250 volts. The module can also send blown fuse diagnostic information to the bus interface unit. The IC670MDL740 positive logic output module has a maximum inrush current of 2 amps, a maximum load current of 0.5 amps, and a minimum load current of 1 mA per point.

可能感興趣的:

GE IC693CHS391

線纜

GE VMIVME-3122

PLC模塊

GE IC670GBIO02H

伺服閥

GE IC693BEM331D

控制器

GE VMIVME-7750

電路板

GE IC670ALG230

通用電氣PLC/可編

GE DS20ODCFBG1BKC

模塊

GE 8121-DI-DC

控制系統模塊

GE IC693MDL752

程控制系統

中央處理

GE WESDAC D20 PS卡件

GE IS215UCVEH2A

接觸器

GE IC693ALG223

器

通信處理

GE IC200ALG328

控制卡

GE IC697MDL75OE

高速計數器模塊

GE IC697ALG230

器

GE 10BASET

渦輪機控制

GE IS215UCVEMO6A

數字量模塊

GE HE693THM884M

CPU模塊開關量模

GE IC698CPE040

處理器

GE IC200ALG326

控制模塊

GE IC693PWR330

塊

繼電器輸

GE UR8FH

開關

GE IC200MDL64OE

變頻器

GE IC693MDL340

出模塊

以太網模

GE DS200RTBAG3AFB

電導率檢測儀

GE IC694MDL645

通用電氣模塊

GE UR9EH

塊

GE DS20ORTBAG3AEB

流量計

GE IC694MDL740

功率內冷模塊

GE DS20ODCFBG1BGB

網卡

GE IS420UCSBH1A

熔斷器開關單元

GE IC695PSD140

模擬量輸入卡

GE IS200VVIBH1CAC

通訊模塊